Skip to content
NPI — NexSource Power Inc.

Planned service for building standby sets

Commercial generator maintenance.

For the generator behind an office, care home, condo, school or store: a set that sits for months and then has to work the first time.

A visit covers the whole standby system, from the transfer switch and batteries to the fuel and the engine, and ends with the set carrying load. Technicians come from Red Deer and work on other makes as well as our own.

NexSource Power service truck parked at night under the northern lights
Field service runs out of the Red Deer shop. If a set fails between visits, the line is answered 24 hours a day.

What has to work in an outage

Six things happen in the first minute. Each one gets checked.

A building's generator is one part of a chain. When the power goes out, every link has to hold, and a generator that runs fine on its own can still leave the building dark.

  1. 01

    The utility fails

    The transfer switch has to notice. A sensing fault or a wrong setting means the generator is never asked to start.

    Checked: Voltage sensing and the time delays set on the switch controller.

  2. 02

    The engine cranks

    Most failed starts come down to a tired battery, a charger that stopped charging, or a block heater that let the engine go cold overnight.

    Checked: Battery condition under load, charger output, block heater operation.

  3. 03

    It comes up to speed

    Old diesel, a clogged filter, or gas pressure that sags once the engine draws hard will stall a set that seemed fine at idle.

    Checked: Fuel condition and filters, or the gas supply pressure while the set is loaded.

  4. 04

    The building transfers

    A set can run perfectly while the switch never moves, or moves and drops the elevator or fire pump because loads come on all at once.

    Checked: A real transfer, watched end to end, with load step timing on the controller.

  5. 05

    It carries the load

    A building that has added rooftop units or a server room since the set was sized can overload it in the first hour.

    Checked: Voltage, frequency and temperatures read off while the set carries load.

  6. 06

    The utility returns

    The switch has to retransfer and the engine has to cool down and shut off. A set that keeps running, or one that dies on retransfer, both mean another call.

    Checked: Retransfer, cool-down timer and the return to automatic.

The engine-side checklist, from oil sampling to the protective shutdowns, is on generator service and maintenance. Switch equipment for a temporary changeover is on transfer switch rentals.

Why idle sets wear out

A generator that barely runs still needs regular visits.

Commercial standby sets can go years with hardly any hours on the meter. Low hours are not the same as low wear, and the schedule has to reflect that.

Ages on the calendar

Batteries, coolant, hoses and belts, and stored diesel all deteriorate whether the engine runs or not. On a standby set that logs a few hours a year, these decide the visit, not the hour meter.

Ages on the hour meter

Oil and filters. A standby set rarely reaches an hours-based change, so it is changed on time instead, and the sample drawn at each change starts a record of what the engine is doing inside.

Changes with the building

A renovation, a new tenant fit-out or a larger chiller changes what the generator has to carry. After any of those, the next visit should include a test at the new load, not just a start.

Testing in an occupied building

Load testing without surprising anyone.

The only way to know a standby set will carry the building is to make it carry something. That can be the building itself, through a planned transfer, or a load bank wired to the generator while the building stays on the utility.

A planned transfer is the more complete test because the switch, the load steps and the building's own equipment are all part of it. It also means a brief interruption, so it is booked with the property manager, and with whoever monitors the fire alarm.

When a transfer is not an option

Care homes during the night, a server room mid-quarter, a store at the till: a load bank lets the engine and alternator work hard without the building noticing. The load banks come from the NexSource fleet and are resistive. If your specification asks for reactive load, mention it when booking. See load bank rentals.

Readings on paper

Voltage, frequency, temperatures and pressures are written down as the set carries load, so the next visit has something to compare against. The record is yours to hand to an inspector or insurer.

If the visit finds a fault

The visit report names it, and the repair is quoted on its own so it can be approved separately. Diagnosis on building sets is covered on commercial generator repair.

Commercial generator repair

If the set has to come out

An overhaul or a rebuild in the shop leaves the building without backup. A rental set can stand in, connected through a temporary transfer arrangement.

Commercial generator rentals

If it is time to replace it

When the repair list keeps growing or the building has outgrown the set, compare the cost of keeping it going with what is in stock to replace it.

Standby generators for sale

Booking a visit

What to send so the first visit is useful.

The buildings
Addresses, building type and who can let a technician into the generator room or enclosure. For a portfolio, a list is enough to start.
Each unit
Make, model, serial and kW from the nameplate, engine hours, and whether it runs on diesel, natural gas or propane.
What it backs up
Life-safety loads only, selected circuits, or the whole building. Note anything that cannot lose power even for a transfer.
Your current routine
Who does the weekly or monthly checks now, how often the set is exercised and whether it is ever run with the building on it.
What you are held to
If an inspector or insurer works to a written standard, such as CSA C282 for emergency generators in buildings, send it or the inspection report.
Past records
Old service reports, oil results and failed-test notes. They keep the next visit from starting at zero.

NexSource works out of one shop, on Queensgate Crescent in Red Deer. Buildings across Alberta are serviced from there, and travel is shown in the quote. For an industrial site, a lease or a prime-power set, see generator service.

Commercial maintenance questions

Questions property managers ask.

How often should a commercial generator be maintained?

Work from the manufacturer's schedule and whatever standard your inspector or insurer holds the building to, then adjust for the unit. Because a standby set runs so little, most of its schedule is set on the calendar. Send the details and the visit plan comes back in writing, showing what is checked on each visit.

We run the generator every week. Isn't that maintenance?

Exercising it proves it starts. It does not change the oil, test the batteries under load or check the transfer switch. A diesel set exercised week after week with nothing connected can also start to wet stack, leaving unburned fuel in the exhaust, which a run under real load or a load bank burns off.

Will the building lose power during maintenance?

Most of a visit is done with the utility carrying the building. A test transfer involves a brief interruption, so it is booked with the property manager in advance, along with whoever monitors the fire alarm. Where a transfer cannot be scheduled, the engine can be tested on a load bank instead.

Do you maintain generators you did not supply?

Yes. Technicians work on other makes as well as the sets NexSource sells and rents. Send the make, model and serial with the booking so the right parts and manual come on the visit.

Can you look after several buildings on one plan?

Yes. Property managers and owners with several sites can have the visits planned together so each unit is seen on schedule and the records sit in one place. What it involves depends on the number of units, where they are and how each runs.

What do we get after a visit?

A written record of what was checked, what was replaced, the load test readings and anything that needs attention before the next visit. Oil results are added as they come back from the lab. Keep it for your inspector or insurer; they decide what satisfies their requirements.

What does commercial generator maintenance cost?

It is quoted per job, with no rate card. The number of units, their size and fuel, how far they are from Red Deer, whether a load bank goes along and what each visit covers all affect the price.

Find out whether it will start before the next outage.

Send the nameplate, the hours and what the generator backs up. The quote lists what each visit covers, how often, and whether a load bank comes along.